E308L-16
Conforms to Certification: AWS A5.4 ASME SFA A5.4
Weld Process: Shielded Manual Metal Arc
| AWS Chemical Composition Requirements | |
| C = 0.04 max | Si= 0.90 max |
| Cr = 18.0-21.0 | P= 0.04 max |
| Ni = 9.0-11.0 | S= 0.03 max |
| Mo = 0.75 max | Cu= 0.75 max |
| Mn = 0.5-2.5 | |
Application
E308L-16 was developed for welding 304L. This electrode deposits a maximum of 0.04% carbon in the weld metal. Type 308L-16 is used extensively for welding of chemical plant equipment and may be used successfully for welding types 321 and 347 steel grades. E308L-16 minimizes the formation of chromium carbides in the weld metal.
| Deposited Chemical Composition % (Typical) | ||
| C = 0.030 | Cr = 19.4 | Si = 0.43 |
| Ni = 9.3 | Mn = 1.65 | P = 0.021 |
| S = 0.02 | ||
| Deposited All Weld Metal Properties % | |
| (Typical) As-Welded | |
| Yield Strength | 84,500 psi |
| Tensile Strength | 55,000 psi |
| Elongation | 40% |
Deposited Charpy-V-Notch Impact Properties %
Not Applicable
| Available Sizes & Recommended Welding Parameters | |||
| Diameter | Voltage | Flat | Amperage Vertical & Overhead |
| 3/32 | 24-28 | 70-85 | 65-75 |
| 1/8 | 26-30 | 85-110 | 80-90 |
| 5/32 | 28-32 | 110-140 | 100-120 |
| 3/16 | 28-32 | 120-160 | 110-130 |
E308H-16
Conforms to Certification: AWS A5.4 ASME SFA A5.4
Weld Process: Shielded Manual Metal Arc
| AWS Chemical Composition Requirements | |
| C = 0.04 – 0.08 | Si = 0.90 max |
| Cr = 18.0 – 21.0 | P = 0.04 max |
| Ni = 9.0 – 11.0 | S = 0.03 max |
| Mo = 0.75 max | Mn = 0.5-2.5 |
Application
E308H-16 electrodes can be used in all the applications specified for type E308-16. In addition it can be used to weld type 304H and similar applications where creep strength is required.
| Deposited Chemical Composition % (Typical) | ||
| C = 0.050 | Cr = 19.20 | Si = 0.42 |
| Ni = 10.30 | Mn = 1.75 | P = 0.01 |
| S = 0.01 | Mo = 0.27 | |
| Deposited All Weld Metal Properties % | |
| (Typical) As-Welded | |
| Yield Strength | 86,000 psi |
| Tensile Strength | 57,000 psi |
| Elongation | 39% |
Deposited Charpy-V-Notch Impact Properties %
Not Applicable
| Available Sizes & Recommended Welding Parameters | |||
| Diameter | Voltage | Flat | Amperage Vertical & Overhead |
| 3/32 | 24-28 | 70-85 | 65-75 |
| 1/8 | 26-30 | 85-110 | 80-90 |
| 5/32 | 28-32 | 110-140 | 100-120 |
| 3/16 | 28-32 | 120-160 | 110-130 |
E308-16
Conforms to Certification: AWS A5.4 ASME SFA A5.4
Weld Process: Shielded Manual Metal Arc
| AWS Chemical Composition Requirements | |
| C = 0.08 max | Si = 0.90 max |
| Cr = 18.0-21.0 | P = 0.04 max |
| Ni = 9.0-11.0 | S = 0.03 max |
| Mo = 0.75 max | Cu = 0.75 max |
| Mn = 0.5-2.5 | |
Application
E308-16 is designed for welding of the following 18-8 stainless steel types: 301, 302, 304 and 308. The weld deposit has the proper chemical content and balance for satisfactory welding of type 308, and therefore is suitable for welding 18-8 types of lower alloy content. Sound weld metal and corrosion resistance equal to or greater than that of the parent metal are assured.
| Deposited Chemical Composition % (Typical) | ||
| C = 0.030 | Cr = 19.4 | Si = 0.43 |
| Ni = 9.30 | Mn = 1.65 | P = 0.021 |
| S = 0.02 | ||
| Deposited All Weld Metal Properties % | |
| (Typical) As-Welded | |
| Yield Strength | 84,500 psi |
| Tensile Strength | 55,000 psi |
| Elongation | 40% |
Deposited Charpy-V-Notch Impact Properties %
Not Applicable
| Available Sizes & Recommended Welding Parameters | |||
| Diameter | Voltage | Flat | Amperage Vertical & Overhead |
| 3/32 | 24-28 | 70-85 | 65-75 |
| 1/8 | 26-30 | 85-110 | 80-90 |
| 5/32 | 28-32 | 110-140 | 100-120 |
| 3/16 | 28-32 | 120-160 | 110-130 |
E2553-16
Conforms to Certification: AWS A5.4 ASME SFA A5.4
Weld Process: Shielded Manual Metal Arc
| AWS Chemical Composition Requirements | |
| C = 0.06 max | Si = 1.0 max |
| Cr = 24.0 – 27.0 | P = 0.04 max |
| Ni = 6.5 – 8.5 | S = 0.03 max |
| Mo = 2.9 – 3.9 | Mn = 0.5 – 1.5 |
| Cu = 1.5 – 2.5 | N = 0.10 – 0.25 |
Application
E2553-16 is a duplex austenitic-ferritic stainless steel with controlled ferrite. It can be used for joining duplex stainless to carbon or low alloy steel. Weld metal deposits by 2553 electrodes combine increased tensile strength with resistance to pitting and stress corrosive cracking.
| Deposited Chemical Composition % (Typical) | ||
| C = 0.03 | Cr = 25.40 | Si = 0.56 |
| Ni = 7.20 | Mn = 0.95 | P = 0.022 |
| S = 0.022 | Mo = 3.10 | N = 0.15 |
| Cu = 2.00 | ||
| Deposited All Weld Metal Properties % | |
| (Typical) As-Welded | |
| Yield Strength | 112,000 psi |
| Tensile Strength | 90,000 psi |
| Elongation | 26.5% |
Deposited Charpy-V-Notch Impact Properties %
Not Applicable
| Available Sizes & Recommended Welding Parameters | |||
| Diameter | Voltage | Flat | Amperage Vertical & Overhead |
| 3/32 | 24-28 | 70-85 | 65-75 |
| 1/8 | 26-30 | 85-110 | 80-90 |
| 5/32 | 28-32 | 110-140 | 100-120 |
| 3/16 | 28-32 | 120-160 | 110-130 |
E2209-16
Conforms to Certification: AWS A5.4 ASME SFA A5.4
Weld Process: Shielded Manual Metal Arc
| AWS Chemical Composition Requirements | |
| C = 0.04 max | Si = 0.90 max |
| Cr = 21.5 – 23.5 | P = 0.04 max |
| Ni = 8.5 – 10.5 | S = 0.03 max |
| Mo = 2.5 – 3.5 | Mn = 0.5 – 2.0 |
| Cu = 0.75 max | N = 0.08 – 0.20 |
Application
E2209-16 is used to weld duplex stainless steels. Welds offer excellent resistance to stress corrosion and cracking.
| Deposited Chemical Composition % (Typical) | ||
| C = 0.03 | Cr = 23.0 | Si = 0.45 |
| Ni = 9.70 | Mn = 0.95 | Mo = 3.00 |
| Deposited All Weld Metal Properties % | |
| (Typical) As-Welded | |
| Yield Strength | 115,000 psi |
| Tensile Strength | 90,000 psi |
| Elongation | 27% |
Deposited Charpy-V-Notch Impact Properties %
Not Applicable
| Available Sizes & Recommended Welding Parameters | |||
| Diameter | Voltage | Flat | Amperage Vertical & Overhead |
| 3/32 | 24-28 | 70-85 | 65-75 |
| 1/8 | 26-30 | 85-110 | 80-90 |
| 5/32 | 28-32 | 110-140 | 100-120 |
| 3/16 | 28-32 | 120-160 | 110-130 |
WWMetallizing Stainless Wire #5
C = 0.15 max
P = 0.06 max
S = 0.03 max
Mn = 8.50 max
Ni = 5.00 max
Cr = 18.0 max
Si = 1.0 max
Fe = Balance
No #5 can be sprayed with most metallizing guns using any fuel gas. Use on seal rings, casings, valve plugs. Use #5 for inside diameters where shrink is a problem or for thick coatings where other materials may crack. Parameters for spraying can be obtained from Spraying Instruction Manuals. Coatings may be machined or ground. Respiratory protection is recommended for spraying this material.
WWMetallizing Stainless Wire #4
C = 0.8 max
P = 0.04 max
S = 0.03 max
Mn = 2.0 max
Ni = 12.0 max
Cr = 17.0 max
Mo = 2.5 max
Si = 1.0 max
Fe = Balance
No #4 wire can be sprayed with most metalizing guns using any fuel gas. Use No #4 wherever a type 316 stainless is specified. Parameters for spraying can be obtained from Spraying Instruction Manuals. Coatings may be machined or ground. Respiratory protection is recommended for spraying this material.
WWMetallizing Stainless Wire #2
C = 0.35 max
P = 0.02 max
S = 0.02 max
Mn = 0.35 max
Ni = 0.50 max
Cr = 13.0 max
Si = 0.50 max
Fe = Balance
Stainless Metallizing Wire #2 can be sprayed with most metalizing guns using any fuel gas. Use #2 wherever a hard coating is required, even where corrosion resistance is not necessary. It is high strength, high elongation and low shrink. Use on cylinder liners, pistons, valve stems, rams or crankshaft bearings. Parameters for spraying can be obtained from Spraying Instruction Manuals. Coatings may be machined or ground. Respiratory protection is recommended for spraying this material.
WWMetallizing Stainless Wire #1
C = 0.08 max
P = 0.03 max
S = 0.03 max
Mn = 2.0 max
Ni = 8.0 max
Cr = 18.0 max
Si = .075 max
Fe = Balance
Stainless Metallizing Wire #1 can be sprayed with most metalizing guns, using only fuel gas. Use #1 wherever a corrosion and wear resistant stainless steel is required. Applications include shafts, value plugs, hydraulic rams. Since it is a high-shrink material, use grooves for coatings more than .030” thick, wherever there are edges. Parameters for spraying can be obtained from Spraying Instruction Manuals. Coatings may be machined or ground. Respiratory protection is recommended for spraying this material.
ERNiMo-3
Conforms to Certification: AWS A5.14 ASME SFA A5.14
Weld Process: GMAW & ASAW Welding Processes
| AWS Chemical Composition Requirements | |
| C = 0.12 max | Cu = 0.50 max |
| Mn = 1.0 max | Ni = Remainder |
| Fe = 4.0 – 7.0 | Co = 2.5 max |
| P = 0.04 max | Cr = 4.0 – 6.0 |
| S = 0.03 max | Mo = 23.0 – 26.0 |
| Si = 1.0 max | V = 0.60 max |
| W = 1.0 max | Other = 0.50 max |
Please Call For More Information and Available Sizes
Application
ERNiMo-3 is a 62.5 Ni, 24 Mo, 6 Fe, 5 Cr alloy that is excellent for welding dissimilar high temperature alloys. Major use is in aircraft engine repair and maintenance.
| Deposited Chemical Composition % (Typical) | ||
| C = 0.05 | Cr = 5.0 | Ni = 62.5 |
| Mo = 24.0 | Fe = 6.0 | |
