ENiCu-7
Conforms to Certification: AWS A5.11 ASME SFA A5.11
Weld Process: Shielded Metal Arc Weld Process (SMAW)
| AWS Chemical Composition Requirements | |
| C = 0.15 max | Cu = Remainder |
| Mn = 4.0 max | Ni = 62.0 – 69.0 |
| Fe = 2.5 max | Al = 0.75 max |
| P = 0.02 max | Ti = 1.0 max |
| S = 0.015 max | Si = 1.5 max |
| Other = 0.50 max | |
Please contact us for more information and availability
Application
ENiCu-7 (NA190) is used for welding materials of nickel-copper alloys to themselves, such as ASTM B127, B163, B164, and B165. Can be used for overlay of clad steels where nickel-copper surfacing is required. Dissimilar welding applications include joining Nickel 200 and copper-nickel alloys.
| Deposited Chemical Composition % (Typical) | ||
| C = 0.03 | Mn = 3.10 | Si = 0.90 |
| Fe = 0.95 | S = 0.006 | P = 0.008 |
| Al = 0.06 | Ti = 0.68 | Cu = 28.0 |
| Ni = 68.0 | ||
| Deposited All Weld Metal Properties % (AW) | |
| Tensile Strength | 75,000 psi |
| Yield Strength | 51,500 psi |
| Elongation | 38% |
Deposited Charpy-V-Notch Impact Properties %
Not applicable
| Recommended Weld Parameters | Amperage (A) | ||
| Diameter of Wire | Voltage (V) | Flat | Vertical and Overhead |
| 3/32 inches (2.4mm) | 24 – 28 | 70 – 85 | 65 – 75 |
| 1/8 inches (3.2mm) | 26 – 30 | 85 – 110 | 80 – 90 |
| 5/32 inches (4.0mm) | 28 – 32 | 110 – 140 | 100 – 120 |
| 3/16 inches (4.8mm) | 28 – 32 | 120 – 160 | 110 – 130 |
ENiCrFe-3
Conforms to Certification: AWS A5.11 ASME SFA A5.11
Weld Process: Shielded Metal Arc Weld Process (SMAW)
| AWS Chemical Composition Requirements | |
| C = 0.10 max | Cu = 0.50 max |
| Mn = 5.0 – 9.5 | Ni = 59.0 min |
| Fe = 10.0 max | Co = 0.12 max |
| P = 0.03 max | Ti = 1.0 max |
| S = 0.015 max | Cr = 13.0 – 17.0 |
| Si = 1.0 max | Cb/Ta = 1.0 – 2.5 |
| Other = 0.50 max | |
Please contact us for more information and availability
Application
Type ENiCrFe-3 (Alloy 182) electrodes are used for welding of nickel-chromium-iron alloys to themselves and for dissimilar welding between nickel-chromium-iron alloys and steels or stainless steels.
The applications include surfacing as well as clad-side welding.
| Deposited Chemical Composition % (Typical) | ||
| C = 0.03 | Mn = 6.5 | Si = 0.42 |
| Cr = 15.25 | Cb/Ta = 1.75 | Fe = 7.4 |
| S = 0.007 | P = 0.011 | Ni = 68.9 |
| Deposited All Weld Metal Properties % (AW) | |
| Tensile Strength | 85,000 psi |
| Yield Strength | 54,000 psi |
| Elongation | 35% |
Deposited Charpy-V-Notch Impact Properties %
Not applicable
| Recommended Weld Parameters | Amperage (A) | ||
| Diameter of Wire | Voltage (V) | Flat | Vertical and Overhead |
| 3/32 inches (2.4mm) | 24 – 28 | 70 – 85 | 65 – 75 |
| 1/8 inches (3.2mm) | 26 – 30 | 85 – 110 | 80 – 90 |
| 5/32 inches (4.0mm) | 28 – 32 | 110 – 140 | 100 – 120 |
| 3/16 inches (4.8mm) | 28 – 32 | 120 – 160 | 110 – 130 |
ENi-1
Conforms to Certification: AWS A5.11 ASME SFA A5.11
Weld Process: Shielded Metal Arc Weld Process (SMAW)
| AWS Chemical Composition Requirements | |
| C = 0.10 max | Cu = 0.25 max |
| Mn = 0.75 max | Ni = 92.0 min |
| Fe = 0.75 max | Al = 1.0 max |
| P = 0.03 max | Ti = 1.0 – 4.0 |
| S = 0.02 max | Si = 1.25 max |
| Other = 0.50 max | |
Please contact us for more information and availability
Application
ENi-1 (Alloy 141) is used for welding of cast and wrought forms of commercially pure nickel. This type of electrode can be used for dissimilar welding between nickel, steel or stainless steels.
| Deposited Chemical Composition % (Typical) | ||
| C = 0.04 | Mn = 0.45 | Si = 0.50 |
| Fe = 0.35 | Ti = 1.05 | P = 0.01 |
| S = 0.004 | Ni = 97.6 | |
| Deposited All Weld Metal Properties % (AW) | |
| Tensile Strength | 65,000 psi |
| Yield Strength | 58,000 psi |
| Elongation | 25% |
Deposited Charpy-V-Notch Impact Properties %
Not applicable
| Recommended Weld Parameters | Amperage (A) | ||
| Diameter of Wire | Voltage (V) | Flat | Vertical and Overhead |
| 3/32 inches (2.4mm) | 24 – 28 | 70 – 85 | 65 – 75 |
| 1/8 inches (3.2mm) | 26 – 30 | 85 – 110 | 80 – 90 |
| 5/32 inches (4.0mm) | 28 – 32 | 110 – 140 | 100 – 120 |
| 3/16 inches (4.8mm) | 28 – 32 | 120 – 160 | 110 – 130 |
ENiCrCoMo-1
Conforms to Certification: AWS A5.11 ASME SFA A5.11
Weld Process: Shielded Metal Arc Weld Process (SMAW)
| AWS Chemical Composition Requirements | |
| C = 0.05 – 0.15 | Cu = 0.50 max |
| Mn = 0.30 – 2.5 | Ni = Remainder |
| Fe = 5.0 max | Co = 9.0 – 15.0 |
| P = 0.03 max | Cr = 21.0 – 26.0 |
| S = 0.015 max | Cb/Ta = 1.0 max |
| Si = 0.75 max | Mo = 8.0 – 10.0 |
| Other = 0.50 max | |
Please contact us for more information and availability
Application
ENiCrCoMo-1 (NA117) electrode is used for welding of nickel-chromium-cobalt-molybdenum alloys. It can be used for overlay cladding when similar alloy is required.
Weld Metal provides optimum strength above 1500ºF up to 2100ºF.
| Deposited Chemical Composition % (Typical) | ||
| C = 0.06 | Mn = 0.46 | Si = 0.36 |
| Fe = 1.52 | S = 0.005 | P = 0.011 |
| Cr = 21.7 | Mo = 8.70 | Co = 12.0 |
| Ni = Balance | ||
| Deposited All Weld Metal Properties % (AW) | |
| Tensile Strength | 110,000 psi |
| Yield Strength | 87,500 psi |
| Elongation | 27% |
Deposited Charpy-V-Notch Impact Properties %
Not applicable
| Recommended Weld Parameters | Amperage (A) | ||
| Diameter of Wire | Voltage (V) | Flat | Vertical and Overhead |
| 3/32 inches (2.4mm) | 24 – 28 | 70 – 85 | 65 – 75 |
| 1/8 inches (3.2mm) | 26 – 30 | 85 – 110 | 80 – 90 |
| 5/32 inches (4.0mm) | 28 – 32 | 110 – 140 | 100 – 120 |
| 3/16 inches (4.8mm) | 28 – 32 | 120 – 160 | 110 – 130 |
ENiCrMo-3
Conforms to Certification: AWS A5.11 ASME SFA A5.11
Weld Process: Shielded Metal Arc Weld Process (SMAW)
| AWS Chemical Composition Requirements | |
| C = 0.10 max | Cu = 0.50 max |
| Mn = 1.0 max | Ni = 55.0 min |
| Fe = 7.0 max | Co = 0.12 max |
| P = 0.03 max | Cr = 20.0 – 23.0 |
| S = 0.02 | Cb/Ta = 3.15 – 4.15 |
| Si = 0.75 max | Mo = 8.00 – 10.0 |
| Other = 0.50 max | |
Please contact us for more information and availability
Application
ENiCrMo-3 (Alloy 112) is an electrode that is used to weld nickel-chromium-molybdenum alloys. Its applications include dissimilar joints between nickel-chromium-molybdenum alloys to either stainless steels, carbon steels or low alloy steels.
These electrodes are used in applications where the temperature ranges up to 1800ºF.
| Deposited Chemical Composition % (Typical) | ||
| C = 0.03 | Mn = 0.35 | Si = 0.34 |
| Fe = 1.5 | S = 0.005 | P = 0.009 |
| Cr = 21.5 | Mo = 9.10 | Cb/Ta = 3.55 |
| Ni = Balance | ||
| Deposited All Weld Metal Properties % (AW) | |
| Tensile Strength | 115,000 psi |
| Yield Strength | 89,000 psi |
| Elongation | 34.5% |
Deposited Charpy-V-Notch Impact Properties %
Not applicable
| Recommended Weld Parameters | Amperage (A) | ||
| Diameter of Wire | Voltage (V) | Flat | Vertical and Overhead |
| 3/32 inches (2.4mm) | 24 – 28 | 70 – 85 | 65 – 75 |
| 1/8 inches (3.2mm) | 26 – 30 | 85 – 110 | 80 – 90 |
| 5/32 inches (4.0mm) | 28 – 32 | 110 – 140 | 100 – 120 |
| 3/16 inches (4.8mm) | 28 – 32 | 120 – 160 | 110 – 130 |
ENiCrMo-10
Conforms to Certification: AWS A5.11 ASME SFA A5.11
Weld Process: Shielded Metal Arc Weld Process (SMAW)
|
AWS Chemical Composition Requirements |
|
| C = 0.02 max | Cu = 0.50 max |
| Mn = 1.0 max | Ni = Remainder |
| Fe = 2.0 – 6.0 | Co = 2.5 max |
| P = 0.03 max | Cr = 20.0 – 22.5 |
| S = 0.015 max | Mo = 12.5 – 14.5 |
| Si = 0.20 max | W = 2.5 – 3.5 |
| V = 0.35 max | Other = 0.50 max |
Please contact us for more information and availability
Application
ENiCrMo-10 (Alloy 22) is used for welding wrought or cast products. Can join stainless and nickel alloys or dissimilar corrosion resistant alloys and cladding. It is suitable for most applications in the as-welded condition.
| Deposited Chemical Composition % (Typical) | ||
| C = 0.014 | Mn = 0.35 | Si = 0.16 |
| Cr = 21.2 | Mo = 13.1 | W = 3.3 |
| P = 0.012 | S = 0.005 | Fe = 3.9 |
| Ni = Balance | ||
| Deposited All Weld Metal Properties % (AW) | |
| Tensile Strength | 113,000 psi |
| Yield Strength | 78,000 psi |
| Elongation | 35.5% |
Deposited Charpy-V-Notch Impact Properties %
Not applicable
| Recommended Weld Parameters | Amperage (A) | ||
| Diameter of Wire | Voltage (V) | Flat | Vertical and Overhead |
| 3/32 inches (2.4mm) | 24 – 28 | 70 – 85 | 65 – 75 |
| 1/8 inches (3.2mm) | 26 – 30 | 85 – 110 | 80 – 90 |
| 5/32 inches (4.0mm) | 28 – 32 | 110 – 140 | 100 – 120 |
| 3/16 inches (4.8mm) | 28 – 32 | 120 – 160 | 110 – 130 |
ENiCrMo-2
Conforms to Certification: AWS A5.11 ASME SFA A5.11
Weld Process: Shielded Metal Arc Weld Process (SMAW)
| AWS Chemical Composition Requirements | |
| C = 0.05 – 0.15 | Cu = 0.50 max |
| Mn = 1.0 max | Ni = Remainder |
| Fe = 17.0 – 20.0 | Co = 0.50 – 2.50 |
| P = 0.04 max | Cr = 20.5 – 23.0 |
| S = 0.03 max | Mo = 8.0 – 10.0 |
| Si = 1.0 max | W = 0.20 – 1.0 |
| Other = 0.50 max | |
Please contact us for more information and availability
Application
ENiCrMo-2 electrodes are used for welding nickel-chromium-molybdenum alloys and clad side of joints in steel clad with a nickel-chromium-moly alloy. Also for welding chromium-moly alloys to steel and other nickel base alloys. These electrodes normally are used in the flat position.
| Deposited Chemical Composition % (Typical) | ||
| C = 0.10 | Mn = 0.57 | Fe = 19.0 |
| Si = 0.55 | Cu = 0.27 | Ni = Remainder |
| Cr = 21.75 | Mo = 9.10 | |
| Deposited All Weld Metal Properties % (AW) | |
| Tensile Strength | 98,500 psi |
| Elongation | 25% |
Deposited Charpy-V-Notch Impact Properties %
Not applicable
| Recommended Weld Parameters | Amperage (A) | ||
| Diameter of Wire | Voltage (V) | Flat | Vertical and Overhead |
| 3/32 inches (2.4mm) | 24 – 28 | 70 – 85 | 65 – 75 |
| 1/8 inches (3.2mm) | 26 – 30 | 85 – 110 | 80 – 90 |
| 5/32 inches (4.0mm) | 28 – 32 | 110 – 140 | 100 – 120 |
| 3/16 inches (4.8mm) | 28 – 32 | 120 – 160 | 110 – 130 |
ENiCrMo-4
Conforms to Certification: AWS A5.11 ASME SFA A5.11
Weld Process: Shielded Metal Arc Weld Process (SMAW)
| AWS Chemical Composition Requirements | |
| C = 0.02 max | Cu = 0.50 max |
| Mn = 1.0 max | Ni = Remainder |
| Fe = 4.0 – 7.0 | Co = 2.5 max |
| P = 0.04 max | Cr = 14.5 – 16.5 |
| S = 0.03 max | Mo = 15.0 – 17.0 |
| Si = 0.20 max | W = 3.0 – 4.5 |
| V = 0.35 max | |
Please contact us for more information and availability
Application
ENiCrMo-4 (Alloy C276) is used for welding materials of similar composition. It can also be used for dissimilar welding between nickel base alloys and stainless steel, also for cladding applications.
| Deposited Chemcial Composition % (Typical) | ||
| C = 0.012 | Mn = 0.40 | Si = 0.14 |
| Fe = 5.5 | Mo = 16.0 | W = 3.25 |
| S = 0.004 | P = 0.012 | Cr = 15.5 |
| Ni = 59.1 | ||
| Deposited All Weld Metal Properties % (AW) | |
| Tensile Strength | 105,000 psi |
| Yield Strength | 79,000 psi |
| Elongation | 38.5% |
Deposited Charpy-V-Notch Impact Properties %
Not applicable
| Recommended Weld Parameters | Amperage (A) | ||
| Diameter of Wire | Voltage (V) | Flat | Vertical and Overhead |
| 3/32 inches (2.4mm) | 24 – 28 | 70 – 85 | 65 – 75 |
| 1/8 inches (3.2mm) | 26 – 30 | 85 – 110 | 80 – 90 |
| 5/32 inches (4.0mm) | 28 – 32 | 110 – 140 | 100 – 120 |
| 3/16 inches (4.8mm) | 28 – 32 | 120 – 160 | 110 – 130 |
ENiCrFe-2
Conforms to Certification: AWS A5.11 ASME SFA A5.11
Weld Process: Shielded Metal Arc Weld Process (SMAW)
| AWS Chemical Composition Requirements | |
| C = 0.10 max | Cu = 0.50 max |
| Mn = 1.0 – 3.5 | Ni = 62.0 min |
| Fe = 12.0 max | Co = 0.12 max |
| P = 0.03 max | Cr = 13.0 – 17.0 |
| S = 0.02 max | Cb/Ta = 0.5 – 3.0 |
| Si = 0.75 max | Mo = 0.50 – 2.50 |
Please contact us for more information and availability
Application
ENiCrFe-2 (Alloy A) electrodes are used for welding of nickel-chromium-iron alloys to themselves, as well as for dissimilar welding between various nickel alloys and carbon or stainless steel. There is a large range of applications from cryogenic temperature up to 1500ºF.
| Deposited Chemical Composition % (Typical) | ||
| C = 0.04 | Mn = 1.75 | Si = 0.32 |
| Cr = 15.5 | Mo = 1.5 | Cb/Ta = 1.25 |
| Fe = 8.5 | S = 0.006 | P = 0.009 |
| Ni = 71.15 | ||
| Deposited All Weld Metal Properties % (AW) | |
| Tensile Strength | 89,000psi |
| Yield Strength | 72,000psi |
| Elongation | 36% |
Deposited Charpy-V-Notch Impact Properties %
Not applicable
| Recommended Weld Parameters | Amperage (A) | ||
| Diameter of Wire | Voltage (V) | Flat | Vertical and Overhead |
| 3/32 inches (2.4mm) | 24 – 28 | 70 – 85 | 65 – 75 |
| 1/8 inches (3.2mm) | 26 – 30 | 85 – 110 | 80 – 90 |
| 5/32 inches (4.0mm) | 28 – 32 | 110 – 140 | 100 – 120 |
| 3/16 inches (4.8mm) | 28 – 32 | 120 – 160 | 110 – 130 |
E71T-GS
Conforms to Certification: AWS A5.20 ASME SFA A5.20
Weld Process: Mig Self Shielding Welding Process
| AWS Chemical Composition Requirements | |
| C = 0.30 max | Cr = 0.20 max |
| Mn = 1.75 max | Ni = 0.50 max |
| Si = 0.90 max | Mo = 0.30 max |
| P = 0.03 max | V = 0.08 max |
| S = 0.03 max | Cu = 0.35 max |
Available Sizes – Diameter X Spool Sizes
.030 x 2#, 10#, 33#
.035 x 2#, 10#, 33#
.045 x 10#, 33#
Application
E71T-GS is a self-shielding all position flux cored welding wire for single pass applications. The use of DC straight polarity minimizes the risk of burn through. It is excellent on lap and fillet welds on thin mild steels.
| Deposited Chemical Composition % (Typical) | ||
| C = 0.21 | Mn = 0.94 | Si = 0.36 |
| P = 0.012 | S = 0.007 | Al = 1.68 |
| Cr = 0.034 | Ni = 0.042 | Mo = 0.035 |
| V = 0.004 | Cu = 0.043 | |
| Deposited All Weld Metal Properties % (As Welded) |
|
| Transverse Tension Test | 76,000 psi |
Deposited Charpy-V-Notch Impact Properties %
32 ft. lbs. (at 0ºF)
| Recommended Operation of Welding Rods (Self-Shielding) |
||
| Diameter | Volts | Amps |
| .035 | 23-29 | 130-260 |
| .045 | 24-30 | 150-350 |
